* Sea-Bird SBE19plus Data File:
* FileName = C:\SeaBird\casts\vlizapril019.hex
* Software Version 1.24
* Temperature SN =  4126
* Conductivity SN =  4126
* System UpLoad Time = apr 17 2002 15:38:24
* ds
* SeacatPlus V 1.3a  SERIAL NO. 4126    17 Apr 2002  13:32:11
* vbatt = 12.6, vlith =  8.4, ioper =  63.3 ma, ipump =  95.9 ma,
* iext01 =  10.5 ma,
* status = not logging
* number of scans to average = 1
* samples = 29266, free = 616011, casts = 22
* mode = profile, minimum cond freq = 3140, pump delay = 45 sec
* ignore magnetic switch = no
* battery type = ALKALINE, battery cutoff =  7.5 volts
* pressure sensor = strain gauge, range = 508.0
* SBE 38 = no, Gas Tension Device = no
* Ext Volt 0 = yes, Ext Volt 1 = no, Ext Volt 2 = no, Ext Volt 3 = no
* echo commands = yes
* output format = raw HEX
* S>
*
* SeacatPlus V 1.3a  SERIAL NO. 4126    17 Apr 2002  13:32:33
* temperature:  17-nov-01
*     TA0 = 1.221633e-03
*     TA1 = 2.748793e-04
*     TA2 = -2.541250e-06
*     TA3 = 2.789542e-07
*     TOFFSET = 0.000000e+00
* conductivity:  17-nov-01
*     G = -1.005099e+00
*     H = 1.450369e-01
*     I = -4.309264e-04
*     J = 5.281733e-05
*     CF0 = 2.639660e+03
*     CPCOR = -9.570000e-08
*     CTCOR = 3.250000e-06
*     CSLOPE = 1.000000e+00
* pressure S/N = 1242, range = 508 psia:  14-nov-01
*     PA0 = 7.780735e-02
*     PA1 = 1.564780e-03
*     PA2 = 6.661129e-12
*     PTCA0 = 5.271810e+05
*     PTCA1 = -5.965753e+00
*     PTCA2 = 3.864335e-01
*     PTCB0 = 2.503600e+01
*     PTCB1 = 4.000000e-04
*     PTCB2 = 0.000000e+00
*     PTEMPA0 = -6.189846e+01
*     PTEMPA1 = 5.140506e+01
*     PTEMPA2 = 2.059025e-02
*     POFFSET = 0.000000e+00
* volt 0: offset = -4.717667e-02, slope = 1.247662e+00
* volt 1: offset = -4.756333e-02, slope = 1.248813e+00
* volt 2: offset = -4.739000e-02, slope = 1.248598e+00
* volt 3: offset = 0.000000e+00, slope = 1.000000e+00
*     EXTFREQSF = 9.999924e-01
* dh
* cast  19 17 Apr 2002 10:33:24 samples 24933 to 26098, avg = 1, stop = mag switch
* S>
# nquan = 9
# nvalues = 41
# units = specified
# name 0 = prdM: Pressure, Strain Gauge [db]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = c0mS/cm: Conductivity [mS/cm]
# name 3 = obs: OBS, Backscatterance (D + A) [NTU]
# name 4 = depSM: Depth [salt water, m]
# name 5 = nbin: number of scans per bin
# name 6 = sal00: Salinity [PSU]
# name 7 = density00: Density [density, Kg/m^3]
# name 8 = flag: flag
# span 0 =      1.009,     21.185
# span 1 =     9.2869,     9.3297
# span 2 =  34.841954,  34.874656
# span 3 =     3.7346,     5.7464
# span 4 =      1.000,     21.000
# span 5 =          0,         13
# span 6 =    32.3095,    32.3316
# span 7 =  1024.9823,  1025.0761
# span 8 = 0.0000e+00, 0.0000e+00
# interval = meters: 1
# start_time = Apr 17 2002 10:33:24
# bad_flag = -9.990e-29
# sensor 0 = Frequency 0  temperature, 4126, 17-Nov-01
# sensor 1 = Frequency 1  conductivity, 4126, 17-Nov-01, cpcor = -9.5700e-08
# sensor 2 = Pressure Number
# sensor 3 = Extrnl Volt  0  backscatterance, 1814, 30 Aug 01
# datcnv_date = Mar 23 2004 12:09:30, 5.30a
# datcnv_in = C:\tjess\ctdcasts\processing\sbe19plus-4126-0201\4126_020417_330.hex C:\tjess\ctdcasts\processing\sbe19plus-4126-0201\4126_0201.con
# datcnv_skipover = 0
# filter_date = Mar 23 2004 12:10:38, 5.30a
# filter_in = C:\tjess\ctdcasts\processing\sbe19plus-4126-0201\cnv\4126_020417_330_C.cnv
# filter_low_pass_tc_A = 0.500
# filter_low_pass_tc_B = 1.000
# filter_low_pass_A_vars = c0mS/cm
# filter_low_pass_B_vars = prdM depSM
# alignctd_date = Mar 23 2004 12:11:40, 5.30a
# alignctd_in = C:\tjess\ctdcasts\processing\sbe19plus-4126-0201\cnv\filter\4126_020417_330_CF.cnv
# alignctd_adv = tv290C 0.500
# loopedit_date = Mar 23 2004 12:12:40, 5.30a
# loopedit_in = C:\tjess\ctdcasts\processing\sbe19plus-4126-0201\cnv\filter\align\4126_020417_330_CFA.cnv
# loopedit_minVelocity = 0.250
# loopedit_excl_bad_scans = yes
# binavg_date = Mar 23 2004 12:13:47, 5.30a
# binavg_in = C:\tjess\ctdcasts\processing\sbe19plus-4126-0201\cnv\filter\align\loop\4126_020417_330_CFAL.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = no, min = 0.000, max = 0.000, value = 0.000
# Derive_date = Mar 23 2004 12:15:26, 5.30a
# Derive_in = C:\tjess\ctdcasts\processing\sbe19plus-4126-0201\cnv\filter\align\loop\bin\4126_020417_330_CFALB.cnv C:\tjess\ctdcasts\processing\sbe19plus-4126-0201\4126_0201.con
# file_type = ascii