* Sea-Bird SBE19plus Data File:
* FileName = F:\New Folder\cast009.hex
* Software Version 1.24
* Temperature SN =  6270
* Conductivity SN =  6270
* System UpLoad Time = feb 09 2012 17:25:46
* SBE 19plus V 2.2c  SERIAL NO. 6270    09 Feb 2012 16:18:11
* vbatt = 11.5, vlith =  7.6, ioper =  61.4 ma, ipump = 101.9 ma,
* iext01 =  13.3 ma, iext2345 =  98.3 ma
* status = not logging
* number of scans to average = 1
* samples = 21985, free = 3111259, casts = 17
* mode = profile, minimum cond freq = 3021, pump delay = 45 sec
* autorun = no, ignore magnetic switch = no
* battery type = NiMH, battery cutoff =  7.8 volts
* test dv/dt step change when voltage is less than  8.7 volts
* pressure sensor = strain gauge, range = 160.0
* SBE 38 = no, OPTODE = no, Gas Tension Device = no
* Ext Volt 0 = yes, Ext Volt 1 = yes
* Ext Volt 2 = yes, Ext Volt 3 = yes
* Ext Volt 4 = yes, Ext Volt 5 = no
* echo characters = yes
* output format = raw HEX
* cast   9 16 Jan 2012 11:41:26 samples 9915 to 10697, avg = 1, stop = mag switch
* S>
# nquan = 12
# nvalues = 41
# units = specified
# name 0 = prdM: Pressure, Strain Gauge [db]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = c0uS/cm: Conductivity [uS/cm]
# name 3 = obs3+: OBS, D & A 3plus [NTU]
# name 4 = depSM: Depth [salt water, m], lat = 51.00
# name 5 = sbeox0Mg/L: Oxygen, SBE 43 [mg/l]
# name 6 = sbeox0PS: Oxygen, SBE 43 [% saturation]
# name 7 = nbin: number of scans per bin
# name 8 = sal00: Salinity, Practical [PSU]
# name 9 = density00: Density [density, Kg/m^3]
# name 10 = svCM: Sound Velocity [Chen-Millero, m/s]
# name 11 = flag: flag
# span 0 =      1.009,     21.185
# span 1 =     7.1669,     7.5251
# span 2 = 3.0769e+04, 3.4638e+04
# span 3 =     2.8666,    39.7829
# span 4 =      1.000,     21.000
# span 5 =    6.34758,   10.48318
# span 6 =   65.58548,  108.53497
# span 7 =          4,         10
# span 8 =    29.9246,    33.7621
# span 9 =  1023.4067,  1026.4657
# span 10 =    1472.98,    1479.47
# span 11 = 0.0000e+00, 0.0000e+00
# interval = meters: 1
# start_time = Jan 16 2012 11:41:26 [Instrument's time stamp, header]
# bad_flag = -9.990e-29
# <Sensors count="8" >
#   <sensor Channel="1" >
#     <!-- Count, Temperature -->
#     <TemperatureSensor SensorID="58" >
#       <SerialNumber>6270</SerialNumber>
#       <CalibrationDate>01-Feb-11</CalibrationDate>
#       <A0>1.31346500e-003</A0>
#       <A1>2.54324100e-004</A1>
#       <A2>4.23633000e-007</A2>
#       <A3>1.20965200e-007</A3>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 0, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>6270</SerialNumber>
#       <CalibrationDate>01-Feb-11</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.02380900e+000</G>
#         <H>1.61556600e-001</H>
#         <I>-2.89678100e-004</I>
#         <J>4.78673700e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Count, Pressure, Strain Gauge -->
#     <PressureSensor SensorID="46" >
#       <SerialNumber>6270</SerialNumber>
#       <CalibrationDate>31-Jan-11</CalibrationDate>
#       <PA0>2.56746500e-001</PA0>
#       <PA1>4.57439000e-004</PA1>
#       <PA2>-4.94457300e-012</PA2>
#       <PTEMPA0>-6.57104100e+001</PTEMPA0>
#       <PTEMPA1>5.16967800e+001</PTEMPA1>
#       <PTEMPA2>-2.84641100e-001</PTEMPA2>
#       <PTCA0>5.28684500e+005</PTCA0>
#       <PTCA1>3.94995700e+001</PTCA1>
#       <PTCA2>-6.07953800e-001</PTCA2>
#       <PTCB0>2.48028750e+001</PTCB0>
#       <PTCB1>-2.50000000e-005</PTCB1>
#       <PTCB2>0.00000000e+000</PTCB2>
#       <Offset>0.000000</Offset>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- A/D voltage 0, OBS, D & A OBS 3+ -->
#     <OBS_3plusSensor SensorID="63" >
#       <SerialNumber>T8498</SerialNumber>
#       <CalibrationDate>5-Feb-10</CalibrationDate>
#       <A0>-2.46120000e-001</A0>
#       <A1>8.67380000e-002</A1>
#       <A2>3.08120000e-006</A2>
#     </OBS_3plusSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- A/D voltage 1, OBS, D & A OBS 3+, 2 -->
#     <OBS_3plusSensor SensorID="63" >
#       <SerialNumber>T8498</SerialNumber>
#       <CalibrationDate>5-Feb-10</CalibrationDate>
#       <A0>-1.12330000e+000</A0>
#       <A1>3.52660000e-001</A1>
#       <A2>4.52410000e-005</A2>
#     </OBS_3plusSensor>
#   </sensor>
#   <sensor Channel="6" >
#     <!-- A/D voltage 2, Altimeter -->
#     <AltimeterSensor SensorID="0" >
#       <SerialNumber>1207</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <ScaleFactor>10.000</ScaleFactor>
#       <Offset>0.000</Offset>
#     </AltimeterSensor>
#   </sensor>
#   <sensor Channel="7" >
#     <!-- A/D voltage 3, Free -->
#   </sensor>
#   <sensor Channel="8" >
#     <!-- A/D voltage 4, Oxygen, SBE 43 -->
#     <OxygenSensor SensorID="38" >
#       <SerialNumber>2087</SerialNumber>
#       <CalibrationDate>29/07/2011</CalibrationDate>
#       <Use2007Equation>1</Use2007Equation>
#       <CalibrationCoefficients equation="0" >
#         <!-- Coefficients for Owens-Millard equation. -->
#         <Boc>0.0000</Boc>
#         <Soc>0.0000e+000</Soc>
#         <offset>0.0000</offset>
#         <Pcor>0.00e+000</Pcor>
#         <Tcor>0.0000</Tcor>
#         <Tau>0.0</Tau>
#       </CalibrationCoefficients>
#       <CalibrationCoefficients equation="1" >
#         <!-- Coefficients for Sea-Bird equation - SBE calibration in 2007 and later. -->
#         <Soc>3.6920e-001</Soc>
#         <offset>-0.4995</offset>
#         <A>-2.9845e-003</A>
#         <B> 1.8602e-004</B>
#         <C>-2.9669e-006</C>
#         <D0> 2.5826e+000</D0>
#         <D1> 1.92634e-004</D1>
#         <D2>-4.64803e-002</D2>
#         <E> 3.6000e-002</E>
#         <Tau20> 1.8600</Tau20>
#         <H1>-3.3000e-002</H1>
#         <H2> 5.0000e+003</H2>
#         <H3> 1.4500e+003</H3>
#       </CalibrationCoefficients>
#     </OxygenSensor>
#   </sensor>
# </Sensors>
# datcnv_date = Feb 15 2012 12:51:13, 7.21 [datcnv_vars = 7]
# datcnv_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plusv2-6270-1102c\6270_120116_330.hex S:\ship\Data_Zeeleeuw\ctdcasts\6270_1102c.con
# datcnv_skipover = 0
# datcnv_ox_hysteresis_correction = yes
# datcnv_ox_tau_correction = yes
# filter_date = Feb 15 2012 12:51:13, 7.21
# filter_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plusv2-6270-1102c\cnv\6270_120116_330_c.cnv
# filter_low_pass_tc_A = 0.500
# filter_low_pass_tc_B = 1.000
# filter_low_pass_A_vars = c0uS/cm
# filter_low_pass_B_vars = prdM depSM
# alignctd_date = Feb 15 2012 12:51:14, 7.21
# alignctd_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plusv2-6270-1102c\cnv\filter\6270_120116_330_cf.cnv
# alignctd_adv = tv290C 0.500, sbeox0Mg/L 0.500, sbeox0PS 0.500
# loopedit_date = Feb 15 2012 12:51:14, 7.21
# loopedit_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plusv2-6270-1102c\cnv\filter\align\6270_120116_330_cfa.cnv
# loopedit_minVelocity = 0.250
# loopedit_surfaceSoak: do not remove
# loopedit_excl_bad_scans = no
# binavg_date = Feb 15 2012 12:51:14, 7.21
# binavg_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plusv2-6270-1102c\cnv\filter\align\loop\6270_120116_330_cfal.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = no, min = 0.000, max = 0.000, value = 0.000
# Derive_date = Feb 15 2012 12:51:14, 7.21 [derive_vars = 3]
# Derive_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plusv2-6270-1102c\cnv\filter\align\loop\bin\6270_120116_330_cfalb.cnv S:\ship\Data_Zeeleeuw\ctdcasts\6270_1102c.con
# file_type = ascii