* Sea-Bird SBE19 Data File:
* FileName = C:\SeaBird\casts\upload jan08\sbe19 upload0801043.hex
* Software Version 1.24
* Temperature SN = 3078
* Conductivity SN = 3078
* System UpLoad Time = jan 09 2008 12:36:16
* ds
* SEACAT PROFILER V3.1d SN 3078   01/09/08  11:32:03.228
* strain gauge pressure sensor: S/N = 2657401433,  range = 1000 psia,  tc = 377
* clk = 32767.773   iop = 175   vmain = 11.5   vlith = 4.8
* mode = PROFILE  ncasts = 56
* sample rate = 1 scan every 0.5 seconds
* minimum raw conductivity frequency for pump turn on = 3208 hertz
* pump delay = 40 seconds
* samples = 31167   free = 84918   lwait = 0 msec
* SW1 = C8   battery cutoff = 7.3 volts
* number of voltages sampled = 2
* logdata = NO
* S>
* dh
* cast 43  12/18  08:20:57   samples 16070 to 16677 sample rate = 1 scan every 0.5 seconds  stop = switch off
* S>
# nquan = 10
# nvalues = 25
# units = specified
# name 0 = prSM: Pressure, Strain Gauge [db]
# name 1 = t090C: Temperature [ITS-90, deg C]
# name 2 = c0uS/cm: Conductivity [uS/cm]
# name 3 = obs: OBS, Backscatterance (D & A) [NTU]
# name 4 = depSM: Depth [salt water, m], lat = 51.00
# name 5 = nbin: number of scans per bin
# name 6 = sal00: Salinity, Practical [PSU]
# name 7 = density00: Density [density, Kg/m^3]
# name 8 = svCM: Sound Velocity [Chen-Millero, m/s]
# name 9 = flag: flag
# span 0 =      1.008,     13.114
# span 1 =     3.5824,     6.8523
# span 2 = 1.6147e+04, 3.2266e+04
# span 3 =    -9.4902,   532.6097
# span 4 =      1.000,     13.000
# span 5 =          2,          9
# span 6 =    16.4424,    31.8234
# span 7 =  1013.0817,  1024.9971
# span 8 =    1441.01,    1474.32
# span 9 = 0.0000e+00, 0.0000e+00
# interval = meters: 1
# start_time = Dec 18 2008 08:20:57 [Instrument's time stamp, header]
# bad_flag = -9.990e-29
# <Sensors count="5" >
#   <sensor Channel="1" >
#     <!-- Frequency 0, Temperature -->
#     <TemperatureSensor SensorID="55" >
#       <SerialNumber>3078</SerialNumber>
#       <CalibrationDate>08-Sep-06</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <A>0.00000000e+000</A>
#       <B>0.00000000e+000</B>
#       <C>0.00000000e+000</C>
#       <D>0.00000000e+000</D>
#       <F0_Old>0.000</F0_Old>
#       <G>4.15415673e-003</G>
#       <H>5.93819685e-004</H>
#       <I>-1.75447422e-006</I>
#       <J>-3.60868250e-006</J>
#       <F0>1000.000</F0>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 1, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>3078</SerialNumber>
#       <CalibrationDate>08-Sep-06</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>0.00000000e+000</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-3.91822094e+000</G>
#         <H>4.68117247e-001</H>
#         <I>8.65663699e-004</I>
#         <J>-1.65323741e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- A/D voltage 0, OBS, Backscatterance (D & A) -->
#     <OBS_DA_3BackscatteranceSensor SensorID="28" >
#       <SerialNumber>1699</SerialNumber>
#       <CalibrationDate></CalibrationDate>
#       <Gain>2000.00</Gain>
#       <Offset>0.000</Offset>
#     </OBS_DA_3BackscatteranceSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- A/D voltage 1, Free -->
#   </sensor>
#   <sensor Channel="5" >
#     <!-- Pressure voltage, Pressure, Strain Gauge -->
#     <PressureSensor SensorID="49" >
#       <SerialNumber>2657401433</SerialNumber>
#       <CalibrationDate>14-Sep-06</CalibrationDate>
#       <A0>5.367824e+002</A0>
#       <A1>-1.437791e-001</A1>
#       <A2>5.432807e-008</A2>
#       <Offset>0.00000</Offset>
#     </PressureSensor>
#   </sensor>
# </Sensors>
# datcnv_date = May 26 2011 16:13:01, 7.21 [datcnv_vars = 5]
# datcnv_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19-3078-0611\3078_071218_230.hex S:\ship\Data_Zeeleeuw\ctdcasts\3078_0611.con
# datcnv_skipover = 0
# filter_date = May 26 2011 16:13:02, 7.21
# filter_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19-3078-0611\cnv\3078_071218_230_c.cnv
# filter_low_pass_tc_A = 0.500
# filter_low_pass_tc_B = 2.000
# filter_low_pass_A_vars = c0uS/cm
# filter_low_pass_B_vars = prSM depSM
# alignctd_date = May 26 2011 16:13:02, 7.21
# alignctd_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19-3078-0611\cnv\filter\3078_071218_230_cf.cnv
# alignctd_adv = t090C 0.500
# loopedit_date = May 26 2011 16:13:02, 7.21
# loopedit_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19-3078-0611\cnv\filter\align\3078_071218_230_cfa.cnv
# loopedit_minVelocity = 0.100
# loopedit_surfaceSoak: do not remove
# loopedit_excl_bad_scans = no
# binavg_date = May 26 2011 16:13:03, 7.21
# binavg_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19-3078-0611\cnv\filter\align\loop\3078_071218_230_cfal.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = no, min = 0.000, max = 0.000, value = 0.000
# Derive_date = May 26 2011 16:13:03, 7.21 [derive_vars = 3]
# Derive_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19-3078-0611\cnv\filter\align\loop\bin\3078_071218_230_cfalb.cnv S:\ship\Data_Zeeleeuw\ctdcasts\3078_0611.con
# file_type = ascii