* Sea-Bird SBE19 Data File:
* FileName = C:\SeaBird\casts\upload030122010.hex
* Software Version 1.24
* Temperature SN = 3078
* Conductivity SN = 3078
* System UpLoad Time = jan 22 2003 15:06:46
* ds
* SEACAT PROFILER V3.1d SN 3078   01/22/03  14:58:33.540
* strain gauge pressure sensor: S/N = 2657401433,  range = 1000 psia,  tc = 377
* clk = 32768.141   iop = 171   vmain = 11.4   vlith = 5.3
* mode = PROFILE  ncasts = 22
* sample rate = 1 scan every 0.5 seconds
* minimum raw conductivity frequency for pump turn on = 3208 hertz
* pump delay = 40 seconds
* samples = 20881   free = 95204   lwait = 0 msec
* SW1 = C8   battery cutoff = 7.3 volts
* number of voltages sampled = 2
* logdata = NO
* S>
* dh
* cast 10  01/21  09:52:38   samples 13902 to 15063 sample rate = 1 scan every 0.5 seconds  stop = switch off
* S>
# nquan = 9
# nvalues = 15
# units = specified
# name 0 = prSM: Pressure, Strain Gauge [db]
# name 1 = t090C: Temperature [ITS-90, deg C]
# name 2 = c0mS/cm: Conductivity [mS/cm]
# name 3 = obs: OBS, Backscatterance (D + A) [NTU]
# name 4 = depSM: Depth [salt water, m]
# name 5 = nbin: number of scans per bin
# name 6 = sal00: Salinity [PSU]
# name 7 = density00: Density [density, Kg/m^3]
# name 8 = flag: flag
# span 0 =      1.008,      8.070
# span 1 =     5.1612,     5.3397
# span 2 =  26.231139,  30.808859
# span 3 =    74.2204,   385.3426
# span 4 =      1.000,      8.000
# span 5 =          1,          9
# span 6 =    26.4832,    31.7850
# span 7 =  1020.9030,  1025.1468
# span 8 = 0.0000e+00, 0.0000e+00
# interval = meters: 1
# start_time = Jan 21 2003 09:52:38
# bad_flag = -9.990e-29
# sensor 0 = Frequency 0  temperature, 3078, 14-Mar-02
# sensor 1 = Frequency 1  conductivity, 3078, 14-Mar-02, cpcor = -9.5700e-08
# sensor 2 = Extrnl Volt  0  backscatterance, 1699
# sensor 3 = Pressure Voltage, 2657401433, 20-Mar-02
# datcnv_date = Jan 22 2004 23:22:54, 5.25
# datcnv_in = C:\tjess\ctdcasts\processing\sbe19-3078-0212VLIZ\3078_030121_130b.hex C:\tjess\ctdcasts\processing\sbe19-3078-0212VLIZ\3078_0212VLIZ.con
# datcnv_skipover = 0
# filter_date = Mar 24 2004 11:11:01, 5.30a
# filter_in = C:\tjess\ctdcasts\processing\sbe19-3078-0212VLIZ\cnv\3078_030121_130b_C.cnv
# filter_low_pass_tc_A = 0.500
# filter_low_pass_tc_B = 2.000
# filter_low_pass_A_vars = c0mS/cm
# filter_low_pass_B_vars = prSM depSM
# alignctd_date = Mar 24 2004 11:11:35, 5.30a
# alignctd_in = C:\tjess\ctdcasts\processing\sbe19-3078-0212VLIZ\cnv\filter\3078_030121_130b_CF.cnv
# alignctd_adv = t090C 0.500
# loopedit_date = Mar 24 2004 11:13:12, 5.30a
# loopedit_in = C:\tjess\ctdcasts\processing\sbe19-3078-0212VLIZ\cnv\filter\align\3078_030121_130b_CFA.cnv
# loopedit_minVelocity = 0.250
# loopedit_excl_bad_scans = yes
# binavg_date = Mar 24 2004 11:13:51, 5.30a
# binavg_in = C:\tjess\ctdcasts\processing\sbe19-3078-0212VLIZ\cnv\filter\align\loop\3078_030121_130b_CFAL.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = no, min = 0.000, max = 0.000, value = 0.000
# Derive_date = Mar 24 2004 11:18:57, 5.30a
# Derive_in = C:\tjess\ctdcasts\processing\sbe19-3078-0212VLIZ\cnv\filter\align\loop\bin\3078_030121_130b_CFALB.cnv C:\tjess\ctdcasts\processing\sbe19-3078-0212VLIZ\3078_0212VLIZ.con
# file_type = ascii