* Sea-Bird SBE19plus Data File:
* FileName = E:\ctd\upload_juli07012.hex
* Software Version 1.50
* Temperature SN =  4126
* Conductivity SN =  4126
* System UpLoad Time = jul 09 2007 09:54:08
* ds
* SeacatPlus V 1.6a  SERIAL NO. 4126    09 Jul 2007  09:48:36
* vbatt = 12.4, vlith =  8.3, ioper =  63.3 ma, ipump =  88.0 ma,
* iext01 =  11.0 ma
* iext23 =  71.4 ma
*
* status = not logging
* number of scans to average = 1
* samples = 15106, free = 544134, casts = 30
* mode = profile, minimum cond freq = 3140, pump delay = 45 sec
* autorun = no, ignore magnetic switch = no
* battery type = alkaline, battery cutoff =  7.3 volts
* pressure sensor = strain gauge, range = 508.0
* SBE 38 = no, Gas Tension Device = no
* Ext Volt 0 = yes, Ext Volt 1 = no, Ext Volt 2 = yes, Ext Volt 3 = no
* echo commands = yes
* output format = raw HEX
* S>
*
* SeacatPlus V 1.6a  SERIAL NO. 4126    09 Jul 2007  09:48:42
* temperature:  08-sep-06
*     TA0 = 1.201298e-03
*     TA1 = 2.822038e-04
*     TA2 = -3.418714e-06
*     TA3 = 3.139171e-07
*     TOFFSET = 0.000000e+00
* conductivity:  08-sep-06
*     G = -1.004160e+00
*     H = 1.447008e-01
*     I = -3.532691e-04
*     J = 4.900649e-05
*     CF0 = 2.639660e+03
*     CPCOR = -9.570000e-08
*     CTCOR = 3.250000e-06
*     CSLOPE = 1.000000e+00
* pressure S/N = 1242, range = 508 psia:  18-sep-06
*     PA0 = 6.774848e-01
*     PA1 = 1.565108e-03
*     PA2 = 1.188614e-11
*     PTCA0 = 5.271677e+05
*     PTCA1 = 2.208672e+01
*     PTCA2 = -9.456675e-02
*     PTCB0 = 2.503600e+01
*     PTCB1 = 4.000000e-04
*     PTCB2 = 0.000000e+00
*     PTEMPA0 = -6.285936e+01
*     PTEMPA1 = 5.237556e+01
*     PTEMPA2 = -2.914526e-01
*     POFFSET = 0.000000e+00
* volt 0: offset = -4.717667e-02, slope = 1.247662e+00
* volt 1: offset = -4.756333e-02, slope = 1.248813e+00
* volt 2: offset = -4.739000e-02, slope = 1.248598e+00
* volt 3: offset = 0.000000e+00, slope = 1.000000e+00
*     EXTFREQSF = 9.999924e-01
* dh
* cast  12 03 Jul 2007 10:23:59 samples 3620 to 4230, avg = 1, stop = mag switch
* S>
# nquan = 10
# nvalues = 45
# units = specified
# name 0 = prdM: Pressure, Strain Gauge [db]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = c0uS/cm: Conductivity [uS/cm]
# name 3 = obs: OBS, Backscatterance (D & A) [NTU]
# name 4 = depSM: Depth [salt water, m], lat = 51.00
# name 5 = nbin: number of scans per bin
# name 6 = sal00: Salinity, Practical [PSU]
# name 7 = density00: Density [density, Kg/m^3]
# name 8 = svCM: Sound Velocity [Chen-Millero, m/s]
# name 9 = flag: flag
# span 0 =      1.009,     23.202
# span 1 =    16.0590,    16.2546
# span 2 = 3.6500e+04, 4.3739e+04
# span 3 =     2.8873,     6.9672
# span 4 =      1.000,     23.000
# span 5 =          3,          8
# span 6 =    28.4233,    34.6297
# span 7 =  1020.6807,  1025.5083
# span 8 =    1502.51,    1510.50
# span 9 = 0.0000e+00, 0.0000e+00
# interval = meters: 1
# start_time = Jul 03 2007 10:23:59 [Instrument's time stamp, header]
# bad_flag = -9.990e-29
# <Sensors count="5" >
#   <sensor Channel="1" >
#     <!-- Count, Temperature -->
#     <TemperatureSensor SensorID="58" >
#       <SerialNumber>4126</SerialNumber>
#       <CalibrationDate>08-Sep-06</CalibrationDate>
#       <A0>1.20129800e-003</A0>
#       <A1>2.82203800e-004</A1>
#       <A2>-3.41871400e-006</A2>
#       <A3>3.13917100e-007</A3>
#       <Slope>1.00000000</Slope>
#       <Offset>0.0000</Offset>
#     </TemperatureSensor>
#   </sensor>
#   <sensor Channel="2" >
#     <!-- Frequency 0, Conductivity -->
#     <ConductivitySensor SensorID="3" >
#       <SerialNumber>4126</SerialNumber>
#       <CalibrationDate>08-Sep-06</CalibrationDate>
#       <UseG_J>1</UseG_J>
#       <!-- Cell const and series R are applicable only for wide range sensors. -->
#       <SeriesR>0.0000</SeriesR>
#       <CellConst>2000.0000</CellConst>
#       <ConductivityType>0</ConductivityType>
#       <Coefficients equation="0" >
#         <A>0.00000000e+000</A>
#         <B>0.00000000e+000</B>
#         <C>0.00000000e+000</C>
#         <D>0.00000000e+000</D>
#         <M>0.0</M>
#         <CPcor>-9.57000000e-008</CPcor>
#       </Coefficients>
#       <Coefficients equation="1" >
#         <G>-1.00416000e+000</G>
#         <H>1.44700800e-001</H>
#         <I>-3.53269100e-004</I>
#         <J>4.90064900e-005</J>
#         <CPcor>-9.57000000e-008</CPcor>
#         <CTcor>3.2500e-006</CTcor>
#         <!-- WBOTC not applicable unless ConductivityType = 1. -->
#         <WBOTC>0.00000000e+000</WBOTC>
#       </Coefficients>
#       <Slope>1.00000000</Slope>
#       <Offset>0.00000</Offset>
#     </ConductivitySensor>
#   </sensor>
#   <sensor Channel="3" >
#     <!-- Count, Pressure, Strain Gauge -->
#     <PressureSensor SensorID="46" >
#       <SerialNumber>1242</SerialNumber>
#       <CalibrationDate>18-Sep-06</CalibrationDate>
#       <PA0>6.77484800e-001</PA0>
#       <PA1>1.56510800e-003</PA1>
#       <PA2>1.18861400e-011</PA2>
#       <PTEMPA0>-6.28593600e+001</PTEMPA0>
#       <PTEMPA1>5.23755500e+001</PTEMPA1>
#       <PTEMPA2>-2.91452600e-001</PTEMPA2>
#       <PTCA0>5.27167700e+005</PTCA0>
#       <PTCA1>2.20867200e+001</PTCA1>
#       <PTCA2>-9.45667500e-002</PTCA2>
#       <PTCB0>2.50360000e+001</PTCB0>
#       <PTCB1>4.00000000e-004</PTCB1>
#       <PTCB2>0.00000000e+000</PTCB2>
#       <Offset>0.000000</Offset>
#     </PressureSensor>
#   </sensor>
#   <sensor Channel="4" >
#     <!-- A/D voltage 0, OBS, Backscatterance (D & A) -->
#     <OBS_DA_3BackscatteranceSensor SensorID="28" >
#       <SerialNumber>1814</SerialNumber>
#       <CalibrationDate>07-May-04</CalibrationDate>
#       <Gain>400.00</Gain>
#       <Offset>0.000</Offset>
#     </OBS_DA_3BackscatteranceSensor>
#   </sensor>
#   <sensor Channel="5" >
#     <!-- A/D voltage 1, Free -->
#   </sensor>
# </Sensors>
# datcnv_date = Dec 14 2010 10:56:42, 7.21 [datcnv_vars = 5]
# datcnv_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plus-4126-0611\4126_070703_215.hex S:\ship\Data_Zeeleeuw\ctdcasts\4126_0611.con
# datcnv_skipover = 0
# filter_date = Dec 14 2010 10:56:43, 7.21
# filter_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plus-4126-0611\cnv\4126_070703_215_c.cnv
# filter_low_pass_tc_A = 0.500
# filter_low_pass_tc_B = 1.000
# filter_low_pass_A_vars = c0uS/cm
# filter_low_pass_B_vars = prdM depSM
# alignctd_date = Dec 14 2010 10:56:43, 7.21
# alignctd_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plus-4126-0611\cnv\filter\4126_070703_215_cf.cnv
# alignctd_adv = tv290C 0.500
# loopedit_date = Dec 14 2010 10:56:44, 7.21
# loopedit_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plus-4126-0611\cnv\filter\align\4126_070703_215_cfa.cnv
# loopedit_minVelocity = 0.250
# loopedit_surfaceSoak: do not remove
# loopedit_excl_bad_scans = no
# binavg_date = Dec 14 2010 10:56:44, 7.21
# binavg_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plus-4126-0611\cnv\filter\align\loop\4126_070703_215_cfal.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = no, min = 0.000, max = 0.000, value = 0.000
# Derive_date = Dec 14 2010 10:56:44, 7.21 [derive_vars = 3]
# Derive_in = S:\ship\Data_Zeeleeuw\ctdcasts\processing\sbe19plus-4126-0611\cnv\filter\align\loop\bin\4126_070703_215_cfalb.cnv S:\ship\Data_Zeeleeuw\ctdcasts\4126_0611.con
# file_type = ascii