* Sea-Bird SBE19plus Data File:
* FileName = C:\Program Files\Sea-Bird\Seaterm\upload090225004.hex
* Software Version 1.59
* Temperature SN =  4126
* Conductivity SN =  4126
* System UpLoad Time = Feb 25 2009 00:20:20
* ds
* SeacatPlus V 1.6a  SERIAL NO. 4126    24 Feb 2009  23:19:34
* vbatt = 12.9, vlith =  7.2, ioper =  63.2 ma, ipump =  67.7 ma,
* iext01 =  10.3 ma
* iext23 =  66.9 ma
*
* status = not logging
* number of scans to average = 1
* samples = 34285, free = 524955, casts = 25
* mode = profile, minimum cond freq = 3140, pump delay = 45 sec
* autorun = no, ignore magnetic switch = no
* battery type = alkaline, battery cutoff =  7.3 volts
* pressure sensor = strain gauge, range = 508.0
* SBE 38 = no, Gas Tension Device = no
* Ext Volt 0 = yes, Ext Volt 1 = no, Ext Volt 2 = yes, Ext Volt 3 = no
* echo commands = yes
* output format = raw HEX
* S>
*
* SeacatPlus V 1.6a  SERIAL NO. 4126    24 Feb 2009  23:19:40
* temperature:  18-aug-07
*     TA0 = 1.203120e-03
*     TA1 = 2.815383e-04
*     TA2 = -3.338941e-06
*     TA3 = 3.107584e-07
*     TOFFSET = 0.000000e+00
* conductivity:  18-aug-07
*     G = -1.003997e+00
*     H = 1.446885e-01
*     I = -3.545539e-04
*     J = 4.947971e-05
*     CF0 = 2.639660e+03
*     CPCOR = -9.570000e-08
*     CTCOR = 3.250000e-06
*     CSLOPE = 1.000000e+00
* pressure S/N = 1242, range = 508 psia:  10-aug-07
*     PA0 = 7.244516e-01
*     PA1 = 1.566113e-03
*     PA2 = 9.058384e-12
*     PTCA0 = 5.271263e+05
*     PTCA1 = 2.649465e+01
*     PTCA2 = -1.934081e-01
*     PTCB0 = 2.503600e+01
*     PTCB1 = 4.000000e-04
*     PTCB2 = 0.000000e+00
*     PTEMPA0 = -6.205500e+01
*     PTEMPA1 = 5.140798e+01
*     PTEMPA2 = 1.964401e-02
*     POFFSET = 0.000000e+00
* volt 0: offset = -4.717667e-02, slope = 1.247662e+00
* volt 1: offset = -4.756333e-02, slope = 1.248813e+00
* volt 2: offset = -4.739000e-02, slope = 1.248598e+00
* volt 3: offset = 0.000000e+00, slope = 1.000000e+00
*     EXTFREQSF = 9.999924e-01
* dh
* cast   4 16 Feb 2009 15:20:01 samples 2443 to 3302, avg = 1, stop = mag switch
* S>
# nquan = 9
# nvalues = 45
# units = specified
# name 0 = prdM: Pressure, Strain Gauge [db]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = c0uS/cm: Conductivity [uS/cm]
# name 3 = obs: OBS, Backscatterance (D & A) [NTU]
# name 4 = depSM: Depth [salt water, m]
# name 5 = nbin: number of scans per bin
# name 6 = sal00: Salinity [PSU]
# name 7 = density00: Density [density, Kg/m^3]
# name 8 = flag: flag
# span 0 =      1.009,     23.202
# span 1 =     3.9241,     4.0336
# span 2 = 2.9913e+04, 3.1438e+04
# span 3 =     3.7876,    10.0509
# span 4 =      1.000,     23.000
# span 5 =          5,         15
# span 6 =    31.8381,    33.6985
# span 7 =  1025.2732,  1026.7628
# span 8 = 0.0000e+00, 0.0000e+00
# interval = meters: 1
# start_time = Feb 16 2009 15:20:01
# bad_flag = -9.990e-29
# sensor 0 = Frequency 0  temperature, 4126, 18-Aug-07
# sensor 1 = Frequency 1  conductivity, 4126, 18-Aug-07, cpcor = -9.5700e-08
# sensor 2 = Pressure Number
# sensor 3 = Extrnl Volt  0  backscatterance, primary, 1814, 07-May-04
# datcnv_date = Apr 06 2009 14:35:43, 7.18c
# datcnv_in = I:\ctdcasts\processing\to_process\4126CASTS\4126_090216_W07.hex S:\ship\ctdcasts\4126_0710.con
# datcnv_skipover = 0
# filter_date = Apr 15 2009 16:38:19, 7.18c
# filter_in = I:\ctdcasts\processing\sbe19plus-4126-0710\cnv\4126_090216_W07_C.cnv
# filter_low_pass_tc_A = 0.500
# filter_low_pass_tc_B = 1.000
# filter_low_pass_A_vars = c0uS/cm
# filter_low_pass_B_vars = prdM depSM
# alignctd_date = Apr 15 2009 16:40:32, 7.18c
# alignctd_in = I:\ctdcasts\processing\sbe19plus-4126-0710\cnv\filter\4126_090216_W07_CF.cnv
# alignctd_adv = tv290C 0.500
# loopedit_date = Apr 15 2009 16:41:25, 7.18c
# loopedit_in = I:\ctdcasts\processing\sbe19plus-4126-0710\cnv\filter\align\4126_090216_W07_CFA.cnv
# loopedit_minVelocity = 0.250
# loopedit_surfaceSoak: do not remove
# loopedit_excl_bad_scans = no
# binavg_date = Apr 15 2009 16:42:59, 7.18c
# binavg_in = I:\ctdcasts\processing\sbe19plus-4126-0710\cnv\filter\align\loop\4126_090216_W07_CFAL.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = no, min = 0.000, max = 0.000, value = 0.000
# Derive_date = Apr 15 2009 16:44:14, 7.18c
# Derive_in = I:\ctdcasts\processing\sbe19plus-4126-0710\cnv\filter\align\loop\bin\4126_090216_W07_CFALB.cnv C:\Documents and Settings\michielt\Desktop\New Folder\4126_0710.con
# file_type = ascii