* Sea-Bird SBE19plus Data File:
* FileName = C:\DATA\SeaBird\upload_4126_feb192007015.hex
* Software Version 1.50
* Temperature SN =  4126
* Conductivity SN =  4126
* System UpLoad Time = feb 19 2007 09:22:14
* ds
* SeacatPlus V 1.6a  SERIAL NO. 4126    19 Feb 2007  08:19:44
* vbatt = 13.4, vlith =  7.9, ioper =  63.2 ma, ipump = 101.4 ma,
* iext01 =  10.2 ma
* iext23 =  65.2 ma
*
* status = not logging
* number of scans to average = 1
* samples = 58574, free = 500666, casts = 59
* mode = profile, minimum cond freq = 3140, pump delay = 45 sec
* autorun = no, ignore magnetic switch = no
* battery type = alkaline, battery cutoff =  7.3 volts
* pressure sensor = strain gauge, range = 508.0
* SBE 38 = no, Gas Tension Device = no
* Ext Volt 0 = yes, Ext Volt 1 = no, Ext Volt 2 = yes, Ext Volt 3 = no
* echo commands = yes
* output format = raw HEX
* S>
*
* SeacatPlus V 1.6a  SERIAL NO. 4126    19 Feb 2007  08:19:51
* temperature:  08-sep-06
*     TA0 = 1.201298e-03
*     TA1 = 2.822038e-04
*     TA2 = -3.418714e-06
*     TA3 = 3.139171e-07
*     TOFFSET = 0.000000e+00
* conductivity:  08-sep-06
*     G = -1.004160e+00
*     H = 1.447008e-01
*     I = -3.532691e-04
*     J = 4.900649e-05
*     CF0 = 2.639660e+03
*     CPCOR = -9.570000e-08
*     CTCOR = 3.250000e-06
*     CSLOPE = 1.000000e+00
* pressure S/N = 1242, range = 508 psia:  18-sep-06
*     PA0 = 6.774848e-01
*     PA1 = 1.565108e-03
*     PA2 = 1.188614e-11
*     PTCA0 = 5.271677e+05
*     PTCA1 = 2.208672e+01
*     PTCA2 = -9.456675e-02
*     PTCB0 = 2.503600e+01
*     PTCB1 = 4.000000e-04
*     PTCB2 = 0.000000e+00
*     PTEMPA0 = -6.285936e+01
*     PTEMPA1 = 5.237556e+01
*     PTEMPA2 = -2.914526e-01
*     POFFSET = 0.000000e+00
* volt 0: offset = -4.717667e-02, slope = 1.247662e+00
* volt 1: offset = -4.756333e-02, slope = 1.248813e+00
* volt 2: offset = -4.739000e-02, slope = 1.248598e+00
* volt 3: offset = 0.000000e+00, slope = 1.000000e+00
*     EXTFREQSF = 9.999924e-01
* dh
* cast  15 19 Dec 2006 14:57:44 samples 11014 to 12047, avg = 1, stop = mag switch
* S>
# nquan = 9
# nvalues = 15
# units = specified
# name 0 = prdM: Pressure, Strain Gauge [db]
# name 1 = tv290C: Temperature [ITS-90, deg C]
# name 2 = c0mS/cm: Conductivity [mS/cm]
# name 3 = obs: OBS, Backscatterance (D & A) [NTU]
# name 4 = depSM: Depth [salt water, m]
# name 5 = nbin: number of scans per bin
# name 6 = density00: Density [density, Kg/m^3]
# name 7 = sal00: Salinity [PSU]
# name 8 = flag: flag
# span 0 =      1.008,      8.070
# span 1 =     8.8812,     9.2250
# span 2 =  26.090698,  35.449562
# span 3 =    10.3429,   508.2115
# span 4 =      1.000,      8.000
# span 5 =          4,         11
# span 6 =  1018.3543,  1025.5632
# span 7 =    23.7610,    33.0124
# span 8 = 0.0000e+00, 0.0000e+00
# interval = meters: 1
# start_time = Dec 19 2006 14:57:44
# bad_flag = -9.990e-29
# sensor 0 = Frequency 0  temperature, 4126, 08-Sep-06
# sensor 1 = Frequency 1  conductivity, 4126, 08-Sep-06, cpcor = -9.5700e-08
# sensor 2 = Pressure Number
# sensor 3 = Extrnl Volt  0  backscatterance, 1814, 30 Aug 2001
# sensor 4 = Extrnl Volt  1  altimeter
# datcnv_date = Jul 10 2007 14:40:46, 7.12
# datcnv_in = S:\ctdcasts\processing\sbe19plus-4126-0611\4126_061219_130b.hex S:\ctdcasts\processing\sbe19plus-4126-0611\4126_0611.con
# datcnv_skipover = 0
# filter_date = Jul 20 2007 10:55:29, 7.12
# filter_in = S:\ctdcasts\processing\sbe19plus-4126-0611\cnv\4126_061219_130b_C.cnv
# filter_low_pass_tc_A = 0.500
# filter_low_pass_tc_B = 1.000
# filter_low_pass_A_vars = c0mS/cm
# filter_low_pass_B_vars = prdM depSM
# alignctd_date = Jul 20 2007 10:56:22, 7.12
# alignctd_in = S:\ctdcasts\processing\sbe19plus-4126-0611\cnv\filter\4126_061219_130b_CF.cnv
# alignctd_adv = tv290C 0.500
# loopedit_date = Jul 20 2007 10:57:20, 7.12
# loopedit_in = S:\ctdcasts\processing\sbe19plus-4126-0611\cnv\filter\align\4126_061219_130b_CFA.cnv
# loopedit_minVelocity = 0.250
# loopedit_surfaceSoak: minDepth = 0.5, maxDepth = 2, useDeckPress = 1
# loopedit_excl_bad_scans = yes
# binavg_date = Jul 23 2007 10:12:03, 7.12
# binavg_in = S:\ctdcasts\processing\sbe19plus-4126-0611\cnv\filter\align\loop\4126_061219_130b_CFAL.cnv
# binavg_bintype = meters
# binavg_binsize = 1
# binavg_excl_bad_scans = yes
# binavg_skipover = 0
# binavg_surface_bin = no, min = 0.000, max = 0.000, value = 0.000
# Derive_date = Jul 23 2007 10:14:44, 7.12
# Derive_in = S:\ctdcasts\processing\sbe19plus-4126-0611\cnv\filter\align\loop\bin\4126_061219_130b_CFALB.cnv S:\ctdcasts\processing\sbe19plus-4126-0611\4126_0611.con
# file_type = ascii